Link2Cell Bluetooth Cordless Phone with Talking Caller ID- 5 Handsets

1. Press [MENU] [#] [3] [3] [1]
2. Enter in the voicemail access number
3. Press [SAVE]
4. [VM] will appear on the display once you have stored the voicemail number.

1. Press [MENU] [#] [1] [2] [2]
2. Change setting from default "B" to "A"
3. Press [SAVE] then [OFF]

1. Press [MENU] [#] [1] [6] [2].
2. Press the [▲] or the [▼] button to turn the handset Caller ID on or off.
   
   Note: The base and each handset are programmed individually.

1. Press the [MENU] [#] [2] [1] [7] on the handset
2. Press [ADD]
3. Enter the phone number you want blocked
4. Press [SAVE]

To store block number from caller list:

1. Press [MENU] [#] [2] [1] [3]
2. Scroll to the number to be blocked
3. Press [SAVE]

Note: If you do not want the first ring from a phone number on the call block list to sound, turn the first ring setting to "Off". Follow this procedure on the handset:

1. Press the [MENU] [#] [1] [7] [3]
2. Select "ON"
3. Press [SAVE]

For additional information, please refer to the Operating Manual.

1. On the handset press [MENU] [#] [2] [1] [7]
2. Press the [▲] or the [▼] to view numbers that are blocked.
3. Press [OFF] to exit the setting.

To unblock a number follow this procedure:

1. On the handset press [MENU] [#] [2] [1] [7]
2. Press the [▲] or the [▼] to select your desired entry
3. Press the soft key [ERASE]
4. Press [SELECT] on "Yes"
5. Press [OFF] to exit the setting.

• Make sure that the base unit has power.

• Check if all cords are secure and plugged in properly from the wall and from the back of the base unit.

• Try to plug the unit to a known working jack then test again.

• If you have a different phone on the same line, and you are also not getting a dial tone, it is possibly a line problem. If that is the case, it is advised to contact your local phone company for further assistance.

1. Unplug your Panasonic phone both from the phone jack.
2. Try relocating the telephone on a different phone jack inside the house.
3. Try using a different line cord if you have any other available.
4. Try using the phone at a friend or neighbors house.

1. Press [MENU] [#] [1] [3] [0] on the Handset
2. Press and hold down the [LOCATOR] button on the base for about 5 seconds until you hear the registration tone
   If all registered handsets starts ringing, press [LOCATOR] again to stop, then repeat this step, procedure needs to be completed within 90 seconds
3. Press [OK] on the handset

1. Press [MENU] [#] [1] [3] [1]
2. Press [▲]/[▼] to select the handset
3. Press [SELECT]
4. Press [▲]/[▼] to select "YES"
5. Press [SELECT] to deregister the handset

1. Press [MENU] [#] [3] [3] [9]
2. Select the desired setting, "ON" or "OFF"
3. Press SAVE then the OFF button

1. Press [MENU] [#] [3] [0] [6] on the handset
2. Key in your preferred 3 digit remote access code
3. Press [OK] or [SAVE]

* * * OR * * *

1. Press [MENU] and scroll down by pressing [▲] or [▼] until "Answering Device" is displayed, then press [OK]
2. Press your [▲] or [▼] repeatedly until "Setting" is displayed, then press [OK]
3. Press your [▲] or [▼] until "Remote Code" is displayed, then press [OK]
4. Key in your preferred 3 digit code
5. Press [OK] or [SAVE] to save the change then press [OFF]

1. On the handset press [MENU] [#] [2] [1] [1]
2. Highlight your desired number of rings by scrolling thru the selection using your [▲] or [▼] button
3. Press [SAVE] then press [OFF]